EMULSOGEN EPA 073


Emulsogen EPA 073
ANIONIC EMULSIFER FOR EMULSION POLYMERIZATION
Emulsogen EPA 073 is used as anionic emulsifier for the emulsion polymerization of monomers like pure acrylic, styrene-acrylic acid esters and vinyl acetate.


Benefits
The use of Emulsogen EPA 073 offers the following advantages:

Product properties:

low VOC
free of alkylphenol ethoxylates (APEO)
readily biodegradable
easy to handle
FDA approved

Performance in emulsion polymerization:

improved stability of the monomer emulsion
low coagulum formation during polymerization
control of particle size of the polymer dispersion
improved viscosity of the polymer dispersions

Performance in paint binders: increases the tinting strength of tinted emulsion paint

Applications
Product group:     Sulfate ester
Active content:    approx. 30%
Appearance:    clear, colorless liquid
pH value:    approx. 7
Solubility:    soluble in water
Density:    approx. 1.05 g/cm3 at 20°C
Viscosity:    approx. 40 mPas 
Boiling point:    approx. 100 °C
Flash point:    > 100 °C
Electrolyte content:    < 0.5%

Anionic emulsifier, wetting and dispersing agent
Composition Alkyl polyethylene glycol ether sulphate with 7 mole ethylene oxide, sodium salt
Product properties 
Active substance content: About 28% in water
Appearance
At 5°C:Clear, colourless liquid
at 20°C: Clear, colourless liquid
at 45°C:Clear, colourless liquid
pH value (DIN EN 1262), 1% in water: About 7.0
Solubility at 20°C: Soluble in water
Density (DIN 51757) At 20°C: about 1,05 g/cm3
At 50°C: about 1,03 g/cm3
Viscosity (Hoeppler) at 25°C: About 40 mPa*s
Boiling point: About 100°C
Flash point: > 100°C
Electrolyte content: < 0,5%
Surface Activity and CMC At 5 g/l active substance in water: About 38 mN/m
Critical micelle concentration: About 1 g/l active substance
Naturally derived carbon content:  None

Profile
Use
Emulsogen® EPA 073 is an anionic surfactant for industrial applications like the following:
Emulsion Polymerization
Emulsogen® EPA 073 is used as an emulsifier for emulsion polymerization of monomers like styrene, acrylic acid esters, methacrylic acid esters and vinyl acetate. The use of
 Emulsogen® EPA 073 offers the following advantages:
— production of polymer dispersions with controlled particle size
— very low grit levels at high solid contents.
Usage levels: 0,5 – 5,0 % based on monomers.
Pigment Preparations
Emulsogen® EPA 073 is used as a wetting agent for inorganic and organic
pigments in preparations
— at high pigment loads
— at low viscosity
— high temperature stability and shelf life.
Usage levels: 15 – 80 % based on the pigments.
Emulsions of solvents, oils and waxes in water
Emulsogen® EPA 073 produces stable, low foaming emulsions of organic solvents, hydrocarbons, oils and waxes in water.
Usage levels: 1 – 20 g/l Emulsogen® EPA 073 in the emulsion.
Storage and Shelf Life
Please keep the product in a dry and clean place. When the product has cooled down to less than 5°C, please heat it up to 25°C – 30°C, after stirring it is ready
to use again. The shelf life is at least two years when stored in tightly closed containers at 20-25°C in a clean and aerated place. After this period the product
should be analyzed for extension of the shelf life.
Preservation
Product is containing 5 ppm a mixture of 5-Chloro-2-Methyl-2H-Isothiazol-3-one and 2-Methlyl-2H-Isothiazol-3-one (3:1)
Safety
Please see Material Safety Data Sheet before handling the material

Bu internet sitesinde sizlere daha iyi hizmet sunulabilmesi için çerezler kullanılmaktadır. Çerezler hakkında detaylı bilgi almak için Kişisel Verilerin Korunması Kanunu mevzuat metnini inceleyebilirsiniz.