Product form : Substance
Substance name : Tylose PSO 810001
Product code : MHPC
Recommended uses of Tylose PSO 810001 :
-Rheological Additive
-Special applications
-Coating material
-Chemical for use in construction
Tylose PSO 810001 is a new type of Methyl Hydroxypropyl Cellulose (MHPC) for thickening systems based on organic solvents - hand sanitizers, paint removers, cleaners, adhesives, pastes and more.
Tylose PSO 810001 is a water-soluble, non-ionic, highly etherified methyl hydroxypropyl cellulose powder.
Tylose PSO 810001 displays increased biostability and very high thickening effects.
Tylose PSO 810001 is ideal for use in paint-stripping pastes.
Tylose PSO 810001 dissolves well in many organic solvents, including:
- ethanol
- acetone
- methanol
- isopropanol
- butyl diglycol
- 1,3-Butanediol
- methylene chloride
- DBE (Dibasic esters)
- DMF (Dimethyl Formamide)
- DMSO (Dimethyl sufloxide)
- NEP (N-Ethyl-2-pyrrolidone)
- BDGA (Butyl diglycol acetate)
- NMP (N-Methyl-2-pyrrolidone)
- 1,2-Propanediol (Propylene glycol)
- TPM (Tripropylene glycol monomethyl ether)
- DPM (Dipropylene glycol monomethyl ether)
Tylose PSO 810001 can be added directly to the organic solvent at room temperature with stirring.
Depending on the solvent, the mixing time is approximately 60 minutes.
The final viscosity is reached within 24 hours.
Thickening organic solvents is a difficult task.
Standard cellulose ethers either do not work well or work only in very few organic solvents or in systems with high water content.
The currently available thickeners for organic solvents have serious drawbacks such as severe limitations in regard to the appropriate solvents, poor performance and complicated processing.
As a solution to these problems SE Tylose has developed Tylose® PSO 810001, a methyl hydroxypropyl cellulose (MHPC) which acts as a thickener for a much broader range of organic solvents.
Tylose PSO 810001 performs exceedingly well in most polar organic solvents, organic solvent mixtures and organic solvent/water systems.
Fields of application include paint strippers, adhesives and fuel pastes.
Typical MHPC grades are known to exhibit inverse solubility in water, which means that they are less or not soluble in hot water, but soluble in cold water.
Tylose PSO 810001 also shows this behaviour in water but its solubility in organic solvents reflects a normal expectation: Increasing solubility with rising temperature.
Thus, in waterless organic solvents, Tylose PSO 810001 can be added directly to organic solvents at room temperature (or below) under stirring. If necessary, the mixture can then be heated.
In case of organic solvent mixtures, Tylose PSO 810001 often works perfectly well, even if none of the components used alone is an appropriate solvent.
It is even possible to use a non-polar solvent in a mixture to suspend Tylose PSO 810001 prior to the dissolution.
The resulting dispersion can then be thickened by adding the polar components of the solvent mixture.
Tylose PSO 810001 provides a flexible high performance method to thicken many solvents and solvent based systems
Tylose PSO 810001 is a new type of Methyl Hydroxypropyl Cellulose (MHPC) for thickening systems based on organic solvents - hand sanitizers, paint removers, cleaners, adhesives, pastes and more.
KEYWORDS:
ethanol, acetone, methanol, isopropanol, butyl diglycol, 1 3-Butanediol, methylene chloride, DBE (Dibasic esters), DMF (Dimethyl Formamide), DMSO (Dimethyl sufloxide)
Appropriate solvents for Tylose PSO 810001 – Some typical examples:
Alcohols:
-Methanol
-Ethanol
-Propanol
-Isopropanol
-Octanol
-Butyl diglycol
-1,3-Butanediol
-Glycerol
-Diethylene glycol
Aldehydes/Ketones:
-Acetone (propanone)
-2-Butanone
Amides:
-DMF (Dimethyl formamide)
-NEP (N-Ethyl-2-pyrrolidone)
-NMP (N-Methyl-2-pyrrolidone)
Esters:
-Dibasic Esters
-BDGA (2-(2-Butoxyethoxy)ethyl acetate)
Ethers:
-DPM (Dipropylene glycol methyl ether)
-TPM (Tripropylene glycol methyl ether)
-THF (Tetrahydrofuran)
-1,3-Dioxolane
Halogenated Carbohydrates:
-Methylene chloride
-Chloroform (trichloromethane)
Others:
-DMSO (Dimethyl sulfoxide)
-Pyridine
Physical state : Solid
Appearance : Powder.
Colour : whitish
Odour : odourless
Odour threshold : No data available
pH : 6 – 8 10g/l
Relative evaporation rate (butylacetate=1) : Not specifically applicable
Melting point / Freezing point : Melting point: Not specifically applicable
Freezing point: Not specifically applicable
Boiling point : Not specifically applicable
Flash point : Not specifically applicable
Auto-ignition temperature : > 170 °C
Flammability (solid, gas) : No data available
Vapour pressure : Vapour pressure: Not specifically applicable
Relative density : Relative vapour density at 20 °C: Not specifically applicable
Density : Density: 1.1 – 1.5 g/cm³ 20 °C
Relative density: Not specifically applicable
Solubility : Water: > 10 g/l @ 20°C
Log Pow : < 0
Viscosity, kinematic : Not specifically applicable
Viscosity, dynamic : Not specifically applicable
Explosive properties : Product is not explosive. Dust may form explosive mixture in air.
Explosive limits : No data available
Minimum ignition energy : > 10 mJ
Fat solubility : No data available
Conbustion class : 5
Smoldering temperature : > 450 °C
pmax : 10 bar
Dust explosion category : ST1
KSt : < 200 bar*m/s
Ignition temperature : > 400 °C
Stability and reactivity of Tylose PSO 810001:
Reactivity : The product is non-reactive under normal conditions of use, storage and transport.
Chemical stability : Stable under normal conditions.
Possibility of hazardous reactions : No dangerous reactions known under normal conditions of use.
Conditions to avoid : No decomposition if stored normally.
Incompatible materials : Strong oxidizing agent.
Hazardous decomposition products : Under normal conditions of storage and use, hazardous decomposition products should not be produced.
Description of necessary first-aid measures of Tylose PSO 810001:
First-aid measures after inhalation : Remove person to fresh air and keep comfortable for breathing. Call a doctor.
First-aid measures after skin contact : Wash skin with plenty of water.
First-aid measures after eye contact : Rinse immediately with plenty of water, also under the eyelids. Consult an ophthalmologist if irritation persists.
First-aid measures after ingestion : Rinse mouth. If symptoms persist, call a physician.
Symptoms caused by exposure:
Symptoms/effects after skin contact : May cause sensitisation of susceptible persons by skin contact.
Symptoms/effects after eye contact : May cause eye irritation
Extinguishing media:
Suitable extinguishing media : Sand. Alcohol resistant foam. Chemical powder. Carbon dioxide. Water spray.
Unsuitable extinguishing media : No data available.
Specific hazards arising from the chemical:
General measures : Avoid dust formation. Do not breathe dust. Forms slippery surfaces with water.
Hazardous decomposition products in case of fire : Toxic fumes may be released. Carbon oxides (CO, CO2).
Special protective equipment and precautions for fire-fighters:
Protection during firefighting : Self-contained breathing apparatus.
Precautions for safe handling of Tylose PSO 810001:
Precautions for safe handling : Ensure good ventilation of the work station. Wear personal protective equipment. Avoid dust formation. Dust may form explosive mixture in air. Keep away from sources of ignition - No smoking.
Hygiene measures : Do not eat, drink or smoke when using this product. Always wash hands after handling the product.
Conditions for safe storage, including any incompatibilities of Tylose PSO 810001:
Storage conditions : Material is hygroscopic. Protect from atmospheric moisture and water.
Information on mixed storage : No special storage requirements.
Individual protection measures, such as personal protective equipment (PPE):
Hand protection : Not required for normal conditions of use. Choosing the proper glove is a decision that depends not only on the type of material, but also on other quality features, which differ for each manufacturer. Please follow the instructions related to the permeability and the penetration time provided by the manufacturer
Eye protection : Not required for normal conditions of use
Skin and body protection : Wear suitable protective clothing
Respiratory protection : In case of insufficient ventilation, wear suitable respiratory equipment.
Other Tylose products:
Tylose HS 100000 YP2 is a water-soluble, non-ionic, highly etherified hydroxyethyl cellulose powder.
It provides increased biostability, very high thickening effects and water retention, moderate foam stabilization, and high solution clarity, gloss appearance, pigment compatibility, and pseudoplasticity.
This grade of hydroxyethyl cellulose (HEC) is particularly well-suited for use in interior paint, non-woven fabric, and toilet cleaner / wc-gel applications.
Tylose HS 30000 YP2 is a hydroxyethyl cellulose powder for applications in interior paints, solid paints, exterior paints, silicon resin paints, tinters, and glazes.
Tylose HS 30000 YP2 is a water-soluble, non-ionic, highly etherified hydroxyethyl cellulose powder.
It provides increased biostability, fast consistency development, high solution clarity and thermal stability, and low sag resitance and water demand.
This grade of hydroxyethyl cellulose (HEC) is ideal for use in emulsion tile adhesives, exterior, interior, and silicone resin paints, drilling fluids, non-woven fabrics, and washing up liquids.
Tylose H 15000 YP2 is a water-soluble, non-ionic hydroxyethyl cellulose powder with standard etherification.
It displays high gloss appearance, pigment compatibility, and water retention, and moderate anti-spattering properties, pseudoplasticity, thickening effects, and wet scrub resistance.
This grade of hydroxyethyl cellulose (HEC) is particularly well-suited for use in silicate and solid paint applications.
Tylose H 10000 NG4 is a water-soluble, non-ionic hydroxyethyl cellulose, in the form of granules, with standard etherification.
It displays moderate thickening effects, foam stabilization, and binding effects, and very good temperature stability.
This grade of hydroxyethyl cellulose (HEC) is particularly well-suited for use in engobe, glaze, liquid detergent, neutral cleaner, shampoo, and toothpaste applications.
Tylose H 6000 YP2 is a water-soluble, non-ionic hydroxyethyl cellulose powder with standard etherifcation.
It provides high gloss appearance and pigment compatibility, good anti-spattering properties, low pseudoplasticity, and moderate thickening effects, wet scrub resistance, and water retention.
This grade of hydroxyethyl cellulose (HEC) is particularly well-suited for use in glaze, powder paint, silicate paint, and tinter applications.
Tylose H 15 YG4 is a water-soluble, non-ionic hydroxyethyl cellulose, in the form of granules, with standard etherification.
It provides very good temperature stability, low thickening effects and plasticity, and good binding effects, protective colloidal effects, and particle size control.
This grade of hydroxyethyl cellulose (HEC) is particularly well-suited for use in engobe, glaze, powder granuling, slip casting, tape casting, and emulsion polymerisation applications.
Tylose H 10 YG4 is a water-soluble, non-ionic hydroxyethyl cellulose, in the form of granules, with standard etherification.
It provides good protective colloidal effects and particle size control.
This grade of hydroxyethyl cellulose (HEC) is particularly well-suited for use in seed coating, rubber glove, and suspension polymerisation (ESP) applications.
Tylose HS 60000 YP2 is a hydroxyethyl cellulose powder recommended for use in interior paints, exterior paints, and silicon resin paints.
Tylose HS 15000 YP2 is a hydroxyethyl cellulose powder recommended for use in interior paints, solid paints, exterior paints, silicon resin paints, tinters, glazes, and gloss effect top coats.
Tylose HS 30000 YP2 is a hydroxyethyl cellulose powder for applications in interior paints, solid paints, exterior paints, silicon resin paints, tinters, and glazes.
Tylose PSO 810001 is a water-soluble, non-ionic, highly etherified methyl hydroxypropyl cellulose powder.
It displays increased biostability and very high thickening effects.
This grade of methyl hydroxypropyl cellulose (MHPC) is ideal for use in paint-stripping pastes.
Tylose CER 406001 is a water-soluble, non-ionic methyl hydroxyethyl cellulose powder with standard etherification.
It displays good plasticity and temperature stability as well as moderate thickening and binding effects.
This grade of methyl hydroxyethyl cellulose (MHEC) is particularly well-suited for use in ceramic coatings – such as engobes and glazes – and extrusion applications.
Tylose HX 6000 YG4 is a chemically modified hydroxyethyl cellulose recommended for use in exterior, interior and semi-gloss paints.
Tylose MOBS 50 G4 is a water-soluble, non-ionic, highly etherified methyl hydroxypropyl cellulose, in the form of granules.
It provides good protective colloidal effects and particle size control. This grade of methyl hydroxypropyl cellulose (MHPC) is particularly well-suited for use in rubber glove, seed coating, and PVC suspension polymerization applications.
Tylose MH 60004 P6 is a water-soluble, non-ionic, modified methyl hydroxyethyl cellulose powder with standard etherification.
It displays very fast consistency development, moderate sag resistance and water demand, very high water retention, and low influence on cement hydration.
This grade of methyl hydroxyethyl cellulose (MHEC) is ideal for use in cement tile adhesives.
Tylose MHS 10012 P6 is a water-soluble, non-ionic, highly etherified, modified methyl hydroxyethyl cellulose powder.
It displays very fast consistency development, high water demand and heat stability, and moderate sag resistance, water retention, and influence on cement hydration.
This grade of methyl hydroxyethyl cellulose (MHEC) is ideal for use in cement one coats.
Tylose MHS 60000 YP4 is a water-soluble, non-ionic, highly etherified methyl hydroxyethyl cellulose powder.
It provides fast consistency development, very high water retention, low sag resistance, water demand, and influence on cement hydration, and high heat stability.
This grade of methyl hydroxyethyl cellulose (MHEC) is ideal for use in emulsion tile adhesives.
Tylose MB 60000 P2 is a water-soluble, non-ionic, highly etherified methyl hydroxyethyl cellulose powder.
It displays moderate gloss appearance, pigment compatibility, anti-spattering properties, and pseudoplasticity, high thickening effects and wet scrub resistance, and very high water retention.
This grade of methyl hydroxyethyl cellulose (MHEC) is particularly well-suited for use in paint-stripping paste applications.
Tylose MH 100001 P6 is a water-soluble, non-ionic, modified methyl hydroxyethyl cellulose powder with standard etherification.
It displays very fast consistency development, very high water retention, low influence on cement hydration, moderate sag resistance, and moderate water demand.
This grade of methyl hydroxyethyl cellulose (MHEC) is ideal for use in cement skim coats and cement tile adhesives.
Tylose MHS 150003 P4 is a water-soluble, non-ionic, highly etherified, modified methyl hydroxyethyl cellulose powder.
It provides very fast consistency development, high water demand, water retention, and heat stability, and moderate sag resistance and influence on cement hydration.
This grade of methyl hydroxyethyl cellulose (MHEC) is ideal for use in block laying adhesives and gypsum mounting binders and spray plasters.
Tylose HS 1000 YP2 is a water-soluble, non-ionic, highly etherified hydroxyethyl cellulose powder.
It displays increased biostability, high gloss appearance and pigment compatibility, low pseudoplasticity and water retention, moderate wet scrub resistance, and good anti-spattering properties.
This grade of hydroxyethyl cellulose (HEC) is ideal for use in solid paints.
Tylose MH 30000 YP4 is a water-soluble, non-ionic, methyl hydroxyethyl cellulose powder with standard etherification.
It provides increased biostability, low gloss appearance, good anti-spattering properties, and high thickening effects and water retention.
This grade of methyl hydroxyethyl cellulose (MHEC) is ideal for use in cement paints, exterior paints, and silicone resin paints.
Tylose MB 10008 P4 is a water-soluble, non-ionic, highly etherified, modified methyl hydroxyethyl cellulose powder.
It provides moderate consistency development, very high sag resistance and water demand, moderate water retention and influence on cement hydration, and low heat stability.
This grade of methyl hydroxyethyl cellulose (MHEC) is ideal for use in cement tile adhesives.
Tylose MH 10015 P4 is a water-soluble, non-ionic, modified methyl hydroxyethyl cellulose powder with standard etherification.
It provides fast consistency development, very high sag resistance and water demand, moderate water retention and influence on cement hydration, and high heat stability.
This grade of methyl hydroxyethyl cellulose (MHEC) is ideal for use in cement tile adhesives.
Tylose MH 20007 P4 is a water-soluble, non-ionic, modified methyl hydroxyethyl cellulose powder with standard etherification.
It displays fast consistency development, very high sag resistance and water demand, moderate water retention and influence on cement hydration, and high heat stability.
This grade of methyl hydroxyethyl cellulose (MHEC) is ideal for use in cement tile adhesives.
Tylose MHS 30027 P6 is a water-soluble, non-ionic, highly etherified, modified methyl hydroxyethyl cellulose powder.
It displays very fast consistency development, moderate sag resistance and water demand, high water retention and heat stability, and low influence on cement hydration.
This grade of methyl hydroxyethyl cellulose (MHEC) is ideal for use in cement renders and EIFSs.
Tylose H 15000 YP2 is a water-soluble, non-ionic hydroxyethyl cellulose powder with standard etherification.
It displays high gloss appearance, pigment compatibility, and water retention, and moderate anti-spattering properties, pseudoplasticity, thickening effects, and wet scrub resistance.
This grade of hydroxyethyl cellulose (HEC) is particularly well-suited for use in silicate and solid paint applications.
Tylose MH 15002 P6 is a water-soluble, non-ionic, modified methyl hydroxyethyl cellulose powder with standard etherification.
It provides fast consistency development, moderate sag resistance, high water demand and water retention, and low influence on cement hydration.
This grade of methyl hydroxyethyl cellulose (MHEC) is particularly well-suited for use in block laying adhesive and cement render applications.
Tylose MO 60016 P4 is a water-soluble, non-ionic, modified methyl hydroxypropyl cellulose powder with standard etherification.
It provides very fast consistency development, moderate sag resistance and water demand, very high water retention, low influence on cement hydration, and high heat stability.
This grade of methyl hydroxypropyl cellulose (MHPC) is ideal for use in cement one coats.
Tylose MB 15009 P2 is a water-soluble, non-ionic, highly etherified, modified methyl hydroxyethyl cellulose powder.
It displays moderate consistency development and sag resistance, high water demand, water retention, and influence on cement hydration, and low heat stability.
This grade of methyl hydroxyethyl cellulose (MHEC) is ideal for use in cement tile adhesives and EIFSs.
Tylose MH 10016 P4 is a water-soluble, non-ionic, modified methyl hydroxyethyl cellulose powder with standard etherification.
It displays fast consistency development, very high sag resistance and water demand, moderate water retention and influence on cement hydration, and high heat stability.
This grade of methyl hydroxyethyl cellulose (MHEC) is ideal for use in cement tile adhesives.
Tylose MH 200 YP2 is a water-soluble, non-ionic methyl hydroxyethyl cellulose powder with standard etherification.
It displays slow consistency development and low sag resistance, water demand, water retention, and influence on cement hydration.
This grade of methyl hydroxyethyl cellulose (MHEC) is particularly well-suited for use in emulsion decorative render and distemper paint applications.
Tylose MH 6000 YP4 is a water-soluble, non-ionic methyl hydroxyethyl cellulose powder with standard etherification.
It provides fast consistency development, low sag resistance and water demand, moderate water retention, and low influence on cement hydration.
This grade of methyl hydroxyethyl cellulose (MHEC) is ideal for use in grouts, lime-wash paints, and powder paints.
Tylose MB 3003 P4 is a water-soluble, non-ionic, highly etherified, modified methyl hydroxyethyl cellulose powder.
It provides moderate consistency development, high sag resistance, water demand, and influence on cement hydration, and low water retention and heat stability. This grade of methyl hydroxyethyl cellulose (MHEC) is particularly well-suited for use in cement tile adhesive applications.
Tylose MH 10007 P4 is a water-soluble, non-ionic, modified methyl hydroxyethyl cellulose powder with standard etherification.
It provides fast consistency development and has moderate sag resistance, water demand, water retention, heat stability, and influence on cement duration.
This grade of methyl hydroxyethyl cellulose (MHEC) is particularly well-suited for use in cement decorative render and EIFS applications.
Tylose MH 60001 P6 is a water-soluble, non-ionic, modified methyl hydroxyethyl cellulose powder with standard etherification.
It provides very fast consistency development, moderate sag resistance and water demand, very high water retention, and low influence on cement hydration.
This grade of methyl hydroxyethyl cellulose (MHEC) is particularly well-suited for use in cement skim coat applications.
Tylose MH 60010 P4 is a water-soluble, non-ionic, modified methyl hydroxyethyl cellulose powder with standard etherification.
It provides very fast consistency development, moderate sag resistance, high water demand and water retention, and moderate influence on cement hydration.
This grade of methyl hydroxyethyl cellulose (MHEC) is ideal for use in cement renders, tile adhesives, and gypsum plasters and compounds.
Tylose MHS 30024 P4 is a water-soluble, non-ionic, highly etherified, modified methyl hydroxyethyl cellulose powder.
It provides fast consistency development, moderate sag resistance and water demand, and high water retention, influence on cement hydration, and heat stability.
This grade of methyl hydroxyethyl cellulose (MHEC) is particularly well-suited for use in block laying and cement tile adhesive applications.
Tylose MHS 30007 P6 is a water-soluble, non-ionic, highly etherified, modified methyl hydroxyethyl cellulose powder.
It displays very fast consistency development, moderate sag resistance and water demand, low influence on cement hydration, and high water retention and heat stability.
This grade of methyl hydroxyethyl cellulose (MHEC) is particularly well-suited for use in cement decorative render and skim coat applications.
Tylose MOT 60000 YP4 is a water-soluble, non-ionic methyl hydroxypropyl cellulose powder with standard etherification.
It displays fast consistency development, very high water retention, low sag resistance, water demand, and influence on cement hydration, and high heat stability.
This grade of methyl hydroxypropyl cellulose (MHPC) is particularly well-suited for use in emulsion joint filler and emulsion tile adhesive applications.
Tylose HS 30000 YP2 is a water-soluble, non-ionic, highly etherified hydroxyethyl cellulose powder.
It provides increased biostability, fast consistency development, high solution clarity and thermal stability, and low sag resitance and water demand.
This grade of hydroxyethyl cellulose (HEC) is ideal for use in emulsion tile adhesives, exterior, interior, and silicone resin paints, drilling fluids, non-woven fabrics, and washing up liquids.
Tylose HX 6000 YG4 is a water-soluble, non-ionic, chemically modified hydroxyethyl cellulose, in the form of granules, with special etherification.
It displays increased biostability, very high gloss appearance and pigment compatibility, excellent anti-spattering properties, low pseudoplasticity, moderate thickening effects and water retention, and high wet scrub resistance.
This grade of hydroxyethyl cellulose (HEC) is particularly well-suited for use in interior paint applications.
Tylose HS 15000 YP2 is a water-soluble, non-ionic, highly etherified hydroxyethyl cellulose powder.
It displays increased biostability, fast consistency development, high gloss appearance, pigment compatibility, and water retention, low sag resistance and water demand, and moderate anti-spattering properties, thickening effects, and influence on cement hydration.
This grade of hydroxyethyl cellulose (HEC) is particularly well-suited for use in tinter, emulsion joint filler, and rubber glove applications.
Tylose HS 6000 YP2 is a water-soluble, non-ionic, highly etherified hydroxyethyl cellulose powder.
It displays increased biostability, moderate thickening effects, high solution clarity, fast consistency development, high gloss appearance and pigment compatibility, and low sag resistance and water demand.
This grade of hydroxyethyl cellulose (HEC) is ideal for use in emulsion decorative renders, glazes, powder and solid paints, tinters, liquid detergents, and toilet cleaners / wc-gels.
Tylose MH 60001 P4 is a water-soluble, non-ionic, modified methyl hydroxyethyl cellulose powder with standard etherification.
It displays very fast consistency development, moderate sag resistance and water demand, very high water retention, and low influence on cement hydration.
This grade of methyl hydroxyethyl cellulose (MHEC) is particularly well-suited for use in cement one coat, cement tile adhesive, gypsum mounting binder, and gypsum troweling compound applications.
Tylose H 30000 YP2 is a water-soluble, non-ionic hydroxyethyl cellulose powder with standard etherification.
It displays very good temperature stability, good binding effects, high gloss appearance, pigment compatibility, and water retention, and moderate anti-spattering properties, wet scrub resistance, and foam stabilization.
This grade of hydroxyethyl cellulose (HEC) is particularly well-suited for use in engobe, glaze, exterior paint, silicate paint, silicone resin paint, welding rod, hair conditioner, and shampoo applications.
Tylovis SE 7 is a starch ether developed especially for dry mixed mortars such as adhesives, plasters and troweling compounds.
Tylovis SE 7 is typically used together with Tylose MC grades in such building products.
It is also compatible with all common dry mixed mortar additives, e.g. air entraining, dispersing and hydrophobic agents.
Tylovis SE 7 gives higher thickening, better slip and sag resistance as well as easy workability.
In adhesives and troweling compounds, which contain higher dosages of methyl cellulose, the stickiness and skin formation can be reduced by addition of Tylovis SE 7.
Tylovis EP 28 is a dispersing and wetting surfactant for cement, lime and gypsum based plasters, renders, mortars and troweling compounds.
It also has a some slight air-entraining properties.
Tylovis EP 28 improves workability, smoothness, plasticity and troweling as well as leveling behaviour of mortars and plasters.
Fine particles of inorganic binders and pigments are much better dispersed throughout mixtures by addition of Tylovis EP 28.
It is highly recommended for gypsum based plasters as it reduces the stickiness of the first leveling and extends working time especially during the final stage.
Tylovis PVA 18 is used in dry mixed mortars in combination with gypsum or cement as a co-binder.
Because of its high adhesive strength to paper, Tylovis PVA 18 is especially recommended for gypsum based adhesives, jointing and troweling compounds, which are used to install plaster board walls and ceilings.
Tylovis PVA 18 reduces the surface tension of water and increases workability and pumpability of mortars.
Other TYLOSE products:
Tylose H grades:
Tylose H 10 YG4
Tylose H 15 YG4
Tylose H 20 P2
Tylose H 20 YG4
Tylose H 200 NP2
Tylose H 300 NG4
Tylose H 300 P2
Tylose H 300 YP2
Tylose H 4000 NG4
Tylose H 6000 YP2
Tylose H 10000 NG4
Tylose H 10000 P2
Tylose H 15000 YP2
Tylose H 30000 YP2
Tylose H 60000 YP2
Tylose H 100000 YP2
Tylose H 200000 YP2
Tylose HA grades:
Tylose HA 40 YP2
Tylose HC grades:
Tylose HC 30000 YP2
Tylose HS grades:
Tylose HS 250 YG4
Tylose HS 6000 YP2
Tylose HS 15000 YP2
Tylose HS 30000 YP2
Tylose HS 60000 YP2
Tylose HS 100000 YP2
Tylose HX grades:
Tylose HX 500 T
Tylose HX 6000 YG4 Plus
Special grades:
Tylose CER 409001
Tylose EHH
Tylose H 4070 NG4
Tylose H 100070 NP2
Tylose HC 50 NP2